PDF Agency

Hitec ECLIPSE 7 Pdf User Manuals. View online or download Hitec ECLIPSE 7 Owner’s Manual. View and Download HITEC Eclipse 7 Pro user manual online. 7 Channel GHz Aircraft Radio Control System. Eclipse 7 Pro Remote Control pdf manual. Does anyone have a copy of the manual for the Eclipse 7 that is not missing pages 44 and 45, every PDF I have found goes pg 42,43,4,5,46,

Author: Nikokasa Daijin
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Politics
Published (Last): 14 August 2018
Pages: 18
PDF File Size: 19.51 Mb
ePub File Size: 20.87 Mb
ISBN: 795-1-43827-323-3
Downloads: 90260
Price: Free* [*Free Regsitration Required]
Uploader: Brarisar

Page 11 Set-up Use of the Hitec 2.

Glider Model Function Descriptions to the sailplane trimming chart on page 51 for more details. Gimbals Feel the silky smooth action of the new four ball bearing supported gimbals in the Eclipse 7 Pro. However, if you program in too amount of coupling is highly dependent on the model much elevator or rudder travel, the servos may reach configuration.

Release the link button. Page 22 Model Charge Setup the Batteries! Reverse the sign in front of the percentage with the Data -Decrease key.

Page 65 63 Page Glid Model Data Recording Sheet Page 5 Hitec 2. Push the link button for 6 sec. About This Manual Collapse the student’s antenna, and fully extend the instructor’s antenna. For training, the transmitter may be connected to another Hitec 2.

The red module LED glows constantly. Aircraft acro Menu Functions Eclupse limits are designed to provide reasonable protection against harmful interference hitdc a residential installation. Page 48 Competition Glider Quick Setup Instructions and down travel for each flap, which is handy for models the F A offset see previous step. A good starting point is to limit This function is turned on with the Flt. If hitc model happens to have a V-tail, all the functions are the same, except for the response of the two tail controls.

  LIBRO YURUPARI PDF

HITEC Eclipse 7 Pro User Manual

Telemetry system Information When you first turn on your transmitter, the first screen shown below appears on the LCD display. Switch power back on. Now the swash should properly respond to aileron. Usually only a small amount of rudder is their travel limits before full stick motion has occurred. Before flying, or even starting the engine, BE SURE that the model number appearing in the higher right of the display matches the model that you are about to fly!

In order to change modeplease adjust Tension Screws and Mode Screws according to below figures. Page 64 Charge the Batteries! Press the Up or Down arrow Eclipse 7 Pro to service center. Please note that for best results, trimming should be done in near-calm conditions. Airplane Model Function Descriptions Page 25 Model Setup Functions Flashing 4. Operating With A Trainer Cord Don’t show me this message again. Notes On Servos Neutralize controls, then half-roll the model.

Transmitter Input Buttons By pressing ‘print’ button you will janual only current page. You set them up manjal the Model Setup menus see page?? Wait for the system to boot and control over the model. Functions relating specifically to gliders and helicopters may be found in the following sections.

  EM NEU 2008 HAUPTKURS ARBEITSBUCH PDF

hktec

HITEC ECLIPSE 7 PRO INSTRUCTION MANUAL Pdf Download.

A wing that generates lift also generates a drag component called induced drag, meaning that drag is induced as a by-product of the lifting wing. Set-up Use of the Hitec 2. Set-up Use of the Hitec 2.

Move the left-hand stick left-and right again and verify the rudder moves the right direction. Radio Installation Notes In the HELI menus, these are automatically called up whenever you switch to a new condition.

Page 52 Glider Model Function Descriptions to the sailplane trimming chart on page 51 for more details. Page 12 openings and cause erratic operation or loss of control. Helicopter Setup Instructions You begin at set point 1, idle. Transmitter Input Buttons The buttons are used for different things as follows: Rest – Data Reset WAR menu will be displayed. Press the Cursor Right key once to get to the elevator setting menu the Numeral 2 and percentage sign will be flashing.

Flight conditions are a very fclipse, and set up a desired value of expo for each flight unusual feature for a system in the class of the Eclipse 7 Pro condition. Enter text from picture: