PDF Agency

Manufacturer name, Eltako. Manufacturer number, TLZEV+UC. GTIN, Country of origin, Germany. Customs tariff number, gThe Standardg TLZ12 8E 23 V UC replaces the TLZ12N0 V and TLZ12 8E V+V uC. gThe Allrounderg TLZ12D 23 V UC replaces the TLZ12M V+V uC. g The Simpleg . Also visit TLZ12D V +UC. Eltako Staircase time switch TLZplus 1; 2; 3; 4 Matching products. Eltako Staircase time switchTLZ Manufacturer, Eltako. Manufacturer.

Author: Tausho Kajizil
Country: Benin
Language: English (Spanish)
Genre: Software
Published (Last): 22 September 2015
Pages: 412
PDF File Size: 18.93 Mb
ePub File Size: 4.65 Mb
ISBN: 630-7-98108-236-3
Downloads: 31712
Price: Free* [*Free Regsitration Required]
Uploader: Moogukree

Fluorescent lamp load, with ballast in DUO circuit or without ballast: If the contact is used for controlling switching devices which do not perform zero passage switching themselves, N should not be connected because the additional closing delay otherwise causes the opposite effect.

When selecting an installation site for light, wind and multi sensors, ensure that the sensors are not in the shadow of the fltako being monitored. It blinks while the relay contact is open closedand etako continuously ON as long as the relay contact is closed open. This display refers to the cumulative value in segment 3.

Eltako Tlz61np230v UC Timer per Luce

Loads drawing more than mA are consistently defined as loads which should cause the line power to be connected. An LED behind the rotary switch indicates rain detection, at which point output 4 tlz12-e8-230v. With the upper rotary switch this impulse switch can be partly or completely excluded from central control: If the function self-learn is not required, set the rotary switch to A automatic OFF. The display is subdivided into 3 fields.

Eltako Tlz61npv UC Timer per Luce | eBay

A1, A7 and A8 need the same potential as L. Zero passage switching with soft start and soft OFF to protect lamps.

  KIM WOODBURN UNBEATEN PDF

With integrated transformer for electrical isolation between control circuit and switching circuit to comply with the requirements for safety extra-low voltage. Connection example page H8. After an interruption, the timing period is restarted.

In the position only the rotating field is monitored, independent from the mains voltage. They are indicated on the display and can be blocked if required. Contact position indication with LED below the upper rotary switch. Bistable switching relays help electronic switchgear to reduce heating and current consumption. When selecting an installation site for light, wind and multi sensors, ensure that the sensors are not in the shadow of theobjects being monitored.

The current dimming position as well Standard setting ex factory. Only the control input A1- A2 should be used.

With the Eltako Duplex technology DX the normally potential-free contacts can still switch in zero passage when switching V AC 50Hz and therefore drastically reduce wear. Before working on the current transformers disconnect the voltage paths of the energy meters.

Eltakk one LED connected in a oating mode, in one of the colours: The noiseless electronics is not even audible to a highly sensitive ear – unlike many synchronous motors with mechanical gearboxes.

Function rotary switches 3. Then, impulse switches were also called impulse relays, step switches or latching relays. The ON button is blue. If several faults occur simultaneously, they are each displayed for one second in succession.

rltako Explanation of capacitive load specification: With integrated transformer for electrical isolation between control circuit and switching circuitto comply with the requirements for safety extra-low voltage. Additionally the local advanced automatic reversing system for Venetian blinds at A1 is active: Push-buttons with a glow lamp current up to 50 mA, dependent on the ignition voltage of the glow lamps, can be connected to the control input.

  LUTTERLOH SYSTEM PATTERNS PDF

If the permanent light function is switched on, the function can be activated by pressing the push-button for longer than 1 second. Afterwards the light is dimmed up in dimming time t max.

Soluções Eléctricas –

A fold inrush current has to be calculated for electronic ballast devices. Local control with roller shutter toggle switch connected to terminals A3 and A4. The product descriptions on the internet are valid only for newly manufactured devices at that time. In both settings, the signals of connected rain and wind sensors may also be eltko.

Only universal dimmers with the marking R, L, C recognize automatically the connected load and adjust their dimming function accordingly. The number of the type examination certificate is also indicated there. Otherwise a telegram is tlz12-8e-30v within 20 seconds if the power changes by minimum 10 percent.

Soluções Eléctricas

No local control refer to function RS. Switching operation for children’s rooms: When signals are detected again, each alarm stops automatically. The LED below the upper rotary switch on the front indicates a local or central control. At the end of the time lapse, contact closes and time lapse T2 starts between 0 and 60 seconds. The function ER is selectable. At the same time a dircectly dimmable lamp can be connected to the dimmer switch EUD A full telegram comprising meter reading and power status is transmitted every 10 minutes.